Modes of Operation

Mitmproxy has four modes of operation that allow you to use mitmproxy in a variety of scenarios:

  • Regular (the default)
  • Transparent
  • Reverse Proxy
  • Upstream Proxy

Now, which one should you pick? Use this flow chart:


Regular Proxy

Mitmproxy’s regular mode is the simplest and the easiest to set up.

  1. Start mitmproxy.
  2. Configure your client to use mitmproxy by explicitly setting an HTTP proxy.
  3. Quick Check: You should already be able to visit an unencrypted HTTP site through the proxy.
  4. Open the magic domain and install the certificate for your device.


Unfortunately, some applications bypass the system HTTP proxy settings - Android applications are a common example. In these cases, you need to use mitmproxy’s transparent mode.

If you are proxying an external device, your network will probably look like this:


The square brackets signify the source and destination IP addresses. Your client explicitly connects to mitmproxy and mitmproxy explicitly connects to the target server.

Transparent Proxy

In transparent mode, traffic is directed into a proxy at the network layer, without any client configuration required. This makes transparent proxying ideal for situations where you can’t change client behaviour. In the graphic below, a machine running mitmproxy has been inserted between the router and the internet:


The square brackets signify the source and destination IP addresses. Round brackets mark the next hop on the Ethernet/data link layer. This distinction is important: when the packet arrives at the mitmproxy machine, it must still be addressed to the target server. This means that Network Address Translation should not be applied before the traffic reaches mitmproxy, since this would remove the target information, leaving mitmproxy unable to determine the real destination.


Common Configurations

There are many ways to configure your network for transparent proxying. We’ll look at two common scenarios:

  1. Configuring the client to use a custom gateway/router/”next hop”
  2. Implementing custom routing on the router

In most cases, the first option is recommended due to its ease of use.

(a) Custom Gateway

One simple way to get traffic to the mitmproxy machine with the destination IP intact, is to simply configure the client with the mitmproxy box as the default gateway.


In this scenario, we would:

  1. Configure the proxy machine for transparent mode. You can find instructions in the Transparent Proxying section.
  2. Configure the client to use the proxy machine’s IP as the default gateway.
  3. Quick Check: At this point, you should already be able to visit an unencrypted HTTP site over the proxy.
  4. Open the magic domain and install the certificate for your device.

Setting the custom gateway on clients can be automated by serving the settings out to clients over DHCP. This lets set up an interception network where all clients are proxied automatically, which can save time and effort.

Troubleshooting Transparent Mode

Incorrect transparent mode configurations are a frequent source of error. If it doesn’t work for you, try the following things:

  • Open mitmproxy’s event log (press e) - do you see clientconnect messages? If not, the packets are not arriving at the proxy. One common cause is the occurrence of ICMP redirects, which means that your machine is telling the client that there’s a faster way to the internet by contacting your router directly (see the Transparent Proxying section on how to disable them). If in doubt, Wireshark may help you to see whether something arrives at your machine or not.
  • Make sure you have not explicitly configured an HTTP proxy on the client. This is not needed in transparent mode.
  • Re-check the instructions in the Transparent Proxying section. Anything you missed?

If you encounter any other pitfalls that should be listed here, please let us know!

(b) Custom Routing

In some cases, you may need more fine-grained control of which traffic reaches the mitmproxy instance, and which doesn’t. You may, for instance, choose only to divert traffic to some hosts into the transparent proxy. There are a huge number of ways to accomplish this, and much will depend on the router or packet filter you’re using. In most cases, the configuration will look like this:


Reverse Proxy

mitmproxy is usually used with a client that uses the proxy to access the Internet. Using reverse proxy mode, you can use mitmproxy to act like a normal HTTP server:


There are various use-cases:

  • Say you have an internal API running at http://example.local/. You could now set up mitmproxy in reverse proxy mode at http://debug.example.local/ and dynamically point clients to this new API endpoint, which provides them with the same data and you with debug information. Similarly, you could move your real server to a different IP/port and set up mitmproxy in the original place to debug and or redirect all sessions.
  • Say you’re a web developer working on (with a development version running on http://localhost:8000/). You can modify your hosts file so that points to and then run mitmproxy in reverse proxy mode on port 80. You can test your app on the domain and get all requests recorded in mitmproxy.
  • Say you have some toy project that should get SSL support. Simply set up mitmproxy as a reverse proxy on port 443 and you’re done (mitmdump -p 443 -R http://localhost:80/). Mitmproxy auto-detects TLS traffic and intercepts it dynamically. There are better tools for this specific task, but mitmproxy is very quick and simple way to set up an SSL-speaking server.
  • Want to add a non-SSL-capable compression proxy in front of your server? You could even spawn a mitmproxy instance that terminates SSL (-R http://...), point it to the compression proxy and let the compression proxy point to a SSL-initiating mitmproxy (-R https://...), which then points to the real server. As you see, it’s a fairly flexible thing.

Caveat: Interactive Use

Reverse Proxy mode is usually not sufficient to create a copy of an interactive website at different URL. The HTML served to the client remains unchanged - as soon as the user clicks on an non-relative URL (or downloads a non-relative image resource), traffic no longer passes through mitmproxy.

Upstream Proxy

If you want to chain proxies by adding mitmproxy in front of a different proxy appliance, you can use mitmproxy’s upstream mode. In upstream mode, all requests are unconditionally transferred to an upstream proxy of your choice.


mitmproxy supports both explicit HTTP and explicit HTTPS in upstream proxy mode. You could in theory chain multiple mitmproxy instances in a row, but that doesn’t make any sense in practice (i.e. outside of our tests).